MissionControl 0.7.1

 
Discutez ici des publications de notre portail. N'hésitez pas à poster vos remarques, commentaires, voire corrections si vous l'estimez nécessaire.
 
Répondre
Avatar du membre
newsbot
Réactions :
Messages : 835
Enregistré le : 21 avr.avr. 2019, 10:57
Localisation : au chaud sur le serveur
Contact :

MissionControl 0.7.1

Message par newsbot » 07 oct.oct. 2022, 22:35


ndeadly a mis à jour son excellent sysmodule permettant de profiter de toutes sortes de manettes sur Switch. De nombreux bugs ont été corrigés et la logique de configuration des Dualshock4 a été inversée pour ce qui concerne sa barre lumineuse (désormais désactivée par défaut). Parmi les nouvelles manettes supportées, on notera la Wii Balance Board (au stade expérimental pour l'instant) et la 8bitdo SN30 Pro Xbox Cloud Gaming controller.

↓ Nouveautés / Corrections (cliquer pour voir) ↓
This is the fifteenth official release of Mission Control.
This is mostly a bugfix release to push out all of the fixes and improvements that I've been sitting on over the past 6 months. Several improvements and some new configuration options were added for Sony controllers, and experimental Wii Balance Board support mapping center of mass values to left analog stick was added. See below for the full changelog.
New users landing on this release page should first check out the readme on the main project page for the official project documentation. There you can find installation and usage instructions along with an FAQ section that will answer most of your questions.
New configuration options
The following additional/modified settings are now available under this [misc] section of the config .ini file.
  • enable_dualshock4_lightbar Enable/disable the coloured LED lightbar on Sony Dualshock4 controllers.
  • enable_dualsense_lightbar Enable/disable the coloured LED lightbar on Sony Dualsense controllers.
  • enable_dualsense_player_leds Enable/disable the white player indicator LEDs below the Dualsense touchpad.
  • dualsense_vibration_intensity Set Dualsense vibration intensity, 12.5% per increment. Valid range [1-8] where 1=12.5%, 8=100%.
Please note that the disable_sony_leds setting no longer exists, and has been replaced by enable_dualshock4_lightbar and enable_dualsense_lightbar (with inverted logic). If you have been using this setting to date, you will need to update your missioncontrol.ini file accordingly.
See here for full instructions on configuring the sysmodule via the .ini file
Changelog:
  • Added experimental support for Wii Balance Board.
  • Added support for 8bitdo SN30 Pro Xbox Cloud Gaming controller running firmware 2.XX.
  • Added mc IPC service for future sysmodule interaction.
  • Added config option to disable Dualsense player LEDs.
  • Added config option to set Dualsense vibration intensity.
  • Split config option for disabling LED lightbar on sony controllers into separate settings for Dualshock4 and Dualsense.
  • Inverted logic for controller config options to match other boolean settings.
  • Fixed Dualsense player LEDs for controllers updated to newer firmware versions.
  • Disabled fade-in effect for Dualsense player LEDs.
  • Lowered default vibration intensity for Dualsense controllers to 50%. This should address user complaints of the vibration being too strong and getting picked up by the motion sensors in certain games.
  • Fixed a regression in Wii extension controller detection that caused WiiU Pro controllers to be incorrectly identified.
  • Wii MotionPlus extension is no longer initialised if motion controls have been disabled in module settings.
  • Wiimote buttons 1/2 now act as L3/R3 when a Classic Controller/ Classic Controller Pro extension is connected.
  • Tweaked battery level mapping for Sony controllers. Should hopefully reduce instances of controllers with low battery being immediately disconnected without warning.
  • Added mutex locks around some sensitive buffer accesses. May improve reliability when pairing controllers.
  • Updated npdm json to eliminate warnings when building from source.
 
Liste des manettes supportées :
  • Nintendo Wii Remote + extensions (Nunchuck, Classic Controller, Classic Controller Pro, SNES Mini)
  • Nintendo WiiU Pro Controller
  • Sony DualShock4 Controller
  • Microsoft Xbox One S/X Controller (modèle bluetooth uniquement)
  • Ouya Controller
  • Gamestick Controller
  • Gembox Controller
  • Ipega Controllers (9062S, 9023, 9096 confirmed working. Others may also work)
  • Xiaomi Mi Controller
  • Steelseries Free Controller
  • GameSir G3s Controller
  • Hori Onyx Controller
  • NVidia shield controller
  • TaTaCon (Taiko drum) Wii extension controller
  • 8bitdo zero
  • GameSir GS4
  • ipega 9076, 9078, 9087
  • PowerA Moga Hero
  • PowerA Moga Pro 2
  • Sony Dualsense Controller*
  • Steelseries Nimbus
  • Razer Serval
  • Mad-Catz C.T.R.L.R
  • PowerA Moga Pro
  • ipega 9017s
  • Mocute 050
  • Hyperkin Scout SNES
  • 8bitdo SN30 Pro Xbox Cloud Gaming controller
 

Attention ! Ce sysmodule nécessite au minimum Atmosphère 1.2.5 !

 

 
Github | GBAtemp

Source : https://hackintendo.com/missioncontrol-0-7-1/
Je suis le petit robot de hackintendo. Je récupère inlassablement les news du site pour qu'on puisse en discuter tranquillement sur le forum.
Répondre